5、水泵有雜音或振動
there is noise
in pump/the pump is vibrating
1、軸中心沒有對正
2、軸彎曲軸承磨損過大
3、葉輪平衡性差
4、地腳螺栓松動
5、裝置不當
6、葉輪局部阻塞
7、吸水高度太高、發生汽蝕
8、泵內掉進雜物
1.the axile cct is not aligning
2.the axile is bend， the bearing wears
much
3.the balance of impeller is not good
4.the foundation bolts are loose
5.the assembly is improper
6.part of the impeller is blocked
7.the suction head is too high to produce
cavitation
8.there are sundries in pump.
1、找正
2、校正或更換軸承
3、進行靜平衡試驗和調整
4、擰緊
5、檢查機組
6、消除雜物
7、降低安裝位置減低安裝高度
8、清除雜物
1.calibrate
2.calibrate it/change the bearing
3.do the static balancing test&adjust
it
4.tighten it
5.check the pump unit
6.remove the sundries
7.reduce the installation site to reduce
the installation ht=
8. remove the sundries
3、水泵出水量不足
the waer yield
of water is not enough
1、進水管路或葉輪有水草雜物
2、轉速過低
3、輸水高度過高
4、泵蓋及葉輪磨損間隙過大
5、填料進氣
6、馬力不足
7、進水管口插入水中-不夠
1. there are waterweeds&sundries in
inlet pipes/impeller
2.the rotate speed is too low
3.water delivery ht= is too high
4.the attrition gap between pump cover
and impeller is too large
5.the padding is air in
6.the horsepower is not engough
7.the depth of inlet pipe under water is
not enough
1、清除水草雜物
2、調整轉數
3、降低輸水高度
4、用紙墊調整間隙至正常
5、壓緊或更換填料
6、加大馬力
7、增加插入水中-至一米左右
1.clear the waterweeds&sundries
2.ajust the rotate speed
3.reduce the water delivery ht=
4.add --- washers to adjust the gaps
5.compact/change padding
6.increase the horsepower
7.make the depth of inlet pipe under
water to one meter
軸流泵的工作原理及特點
1、軸流泵的工作原理
軸流泵與離心泵的工作原理不同，移動式混流泵廠家，它主要是利用葉輪的高速旋轉所產生的推力提水。軸流泵葉片旋轉時對水所產生的升力，不銹鋼混流泵廠家，可把水從下方推到上方。
軸流泵的葉片一般浸沒在被吸水源的水池中。由于葉輪高速旋轉，在葉片產生的升力作用下，南京混流泵廠家，連續不斷的將水向上推壓，使水沿出水管流出。葉輪不斷的旋轉，水也就被連續壓送到高處。
|
登錄后臺
滇公網安備 53011202000392